Targeted Nano-Synergistic Technology · Tiangang Group

Bring recycled PP back to virgin performance.
Use less virgin resin.

At 1.5–3% loading, stiffness, toughness and melt flow move in the same direction. Stiffness and toughness are usually a trade-off. We separate the two mechanisms that control them.

Measured data · third-party tested
+258%
Notched Izod impact of grade-3 recycled PP with 3% E2801
−42%
Pallet cycle time, from 128 s to 74 s
89%
Gloss retention after 1200 h UVB, versus 8% for the conventional route
1.5–3%
Typical loading, masterbatch form, dry-blend ready
185MPa
Tensile strength, 30% GF PA6, on par with PA66
19.7kJ/m²
Notched Izod impact, same system
Grade0
Mildew resistance, highest rating, third-party tested
Problems we are asked about

Four problems. Four specific answers.

Not "superior performance". Each one comes with a number you can check.

Recyclate turns brittle; impact modifiers soften it further

The usual fix is 10–20% POE or LLDPE. Modulus drops, cost rises, melt gets stickier. E2415 restores impact at 1.5–3% without losing modulus — some formulations exceed virgin K8003.

Stiffer or tougher — apparently only one at a time

Conventional nucleators raise crystallinity, and crystallinity is what makes the part brittle. We separate molecular nucleation from intra-molecular lubrication so the two can be controlled independently.

Processing temperature will not come down

Intra-molecular lubrication reduces melt viscosity. In the pallet case, cycle time fell from 128 s to 74 s and daily power use by 1673 kWh — usually worth more than the masterbatch itself.

Mould, mildew and algae, especially outdoors or in water contact

Conventional biocides cannot survive processing heat and often carry odour. Ours withstands above 250 °C, runs clean in spinning and injection, and reaches Grade 0 mildew resistance.

Comparative trial

Returnable pallets: 2% masterbatch replaces 15% LLDPE

Same batch of K8003, two formulations, one test protocol. Left is the standard industry route; right adds 2% Tinasup™ E2625.

Tinasup™ E2625 at 2% · gloss retention after 1200 h UVB89%
Conventional LLDPE route · gloss retention after 1200 h UVB8%

1200 h UVB is a comparative screening test, not a service-life prediction. We report test values and retention rates only.

Property+15% LLDPE+2% E2625
Flexural strength24.6 MPa34.0 MPa
Flexural modulus821 MPa1105 MPa
Gloss retention, 1200 h UVB8%89%
Elongation retention, 2400 h UVA23%95%
Impact retention, 2400 h UVA35%85%
Heat distortion temperature70 °C89 °C
Cycle time per pallet128 s74 s

Full dataset and processing notes

Technology platform

Targeted nano-synergy, three directions

"Targeted" is borrowed from medicine: what matters is not the dose but reaching the right site at the right quantity. In polymers, that means controlling where nanoparticles nucleate, how they disperse and what they act with.

01 / DISPERSION

Nano dispersion

Nano powders added directly are wasted — agglomerated particles show no nano effect. We build functionalised micro-nano dispersions via supercritical CO₂, with our own dispersion equipment and composite carrier technology.

Technical detail
02 / NUCLEATION

Simultaneous stiffening and toughening

Molecular nucleation refines the crystal structure; intra-molecular lubrication improves melt flow. Control them separately and you get stiffness, toughness and processability at once.

Technical detail
03 / ANTIMICROBIAL

Antimicrobial, anti-mildew, anti-algae

Stable above 250 °C, odour-free and low VOC. Suitable for fibre, film, injection moulding and water-contact parts. Grade 0 mildew resistance in third-party testing.

Technical detail
Applications

Already running in these

About

The nanomaterials platform of Tiangang Group

Tinaco was founded in 2013 by Luo Daoyou, former Vice President and Chief Engineer of the Beijing Chemical Industry Research Institute, and became a Tiangang Group company in 2017.

Tiangang has produced light stabilisers since 1991, with three manufacturing sites in Beijing, Cangzhou and Gu'an, a combined capacity above 30,000 t/y and a sales subsidiary in Brussels. The HALS in our masterbatches comes from that chain.

Group and manufacturing

2013
Tinaco founded
30+
Years of team experience
30kt
Group capacity per year
3
Manufacturing sites

Test it before you price it

Tell us your resin grade, processing temperature, part thickness and the property you need to improve. We recommend a grade and dosage, ship 1–5 kg, and follow up with comparative data.

Or call Mr. Luo +86 135 5407 7117 +86 130 0101 5295

Request a sample